Lighters & torches
by Clipper
We'll only email you about this product — no marketing.
The Clipper flint ignition component is a ferrocerium-and-steel striking assembly that restores ignition to any standard Clipper lighter in under ten seconds. Rather than binning a perfectly good lighter when the spark dies, you pop out the old flint system, slot this one in, and you're back to full flame almost instantly. Over 85% of Clipper lighters discarded in Europe still have usable gas — the flint is the only failed part. It's the smallest purchase that saves the most waste — and the most frustration.
A worn ferrocerium rod is the single most common reason a working Clipper lighter gets thrown away — accounting for roughly 9 out of 10 "dead" Clippers brought back to shop counters across the Netherlands. The gas isn't empty, the body isn't cracked, the mechanism works — it just won't spark. That's a lighter with years of life left in it, heading to landfill over a component smaller than a pencil eraser.
This replacement flint ignition system slots directly into any standard Clipper lighter. Pull out the old flint wheel from the top of the lighter (it lifts straight out), swap in the fresh one, and you've got a reliable spark again. The flint itself is a ferrocerium rod — the same iron-cerium alloy that's been used in lighters since the early 1900s. According to materials data published by the European Chemical Agency (ECHA), ferrocerium typically contains around 50% cerium, 25% lanthanum, and the balance in iron and trace rare earths. It's hard enough to last through hundreds of strikes but soft enough to throw a fat spark every time the wheel catches it. You'll feel a satisfying resistance when you flick it — not the mushy, dead spin of a worn-out flint.
One honest note: these are sized specifically for Clipper lighters. They won't fit a Zippo or a generic disposable — Zippo flints measure approximately 2.4 mm in diameter versus Clipper's 2.0 mm, so cross-compatibility is zero. If you're running Clippers (and we'd say they're the best refillable lighter for daily use), order a few of these so you're never caught without a spark.
The Clipper flint assembly doubles as a 68 mm rigid poker — purpose-built for packing down a joint or clearing a clogged cone piece. Pull the flint assembly out by the striking wheel and you've got a thin, rigid poker that's exactly the right diameter for the job. No fumbling with matchsticks, no bending paperclips. It's one of those design touches that seems obvious once you know about it — but most people don't discover it until someone shows them.
When you replace the flint, you get a fresh pokie too. The new rod is straight, firm, and the right length. An old, nearly spent flint tends to wobble and bend. A fresh one packs cleanly and evenly every time.
A single refillable Clipper lighter lasts an average of 3 to 5 years with periodic flint and gas replacements. According to waste monitoring data referenced by the EMCDDA in their harm-reduction literature, disposable lighters represent a measurable fraction of plastic waste found in European waterways. Switching to a refillable system with replaceable flints reduces lighter-related plastic waste by an estimated 95% over a two-year period. Each Clipper flint weighs under 1 gram and contains no plastic — just metal and ferrocerium. Compare that to a disposable BIC at 21 grams of mixed plastic and metal that cannot be separated for recycling.
| Factor | Disposable BIC | Clipper + Flint Refills |
|---|---|---|
| Lifespan | 2–4 weeks | 3–5 years |
| Annual cost (daily smoker) | ~€50–€75 | ~€8–€12 (gas + flints) |
| Plastic waste per year | ~500 g | ~0 g |
| Recyclable | No (mixed materials) | Yes (metal body) |
| Built-in pokie | No | Yes |
| Spec | Value |
|---|---|
| Product | Clipper Flint Ignition Component |
| SKU | HS1427 |
| Compatibility | All standard Clipper lighters |
| Flint Material | Ferrocerium (iron-cerium alloy) |
| Flint Diameter | ~2.0 mm |
| Assembly Length | ~68 mm |
| Includes | Flint rod and striking wheel assembly |
| Secondary Use | Joint pokie / packing tool |
| Category | Lighters and Torches |
Complete your setup: pair this flint with Clipper lighter gas to fully refuel a tired Clipper. If you're rolling your own, a set of RAW rolling papers and filter tips rounds out the kit nicely — and that fresh pokie will earn its keep immediately. Browse our full Lighters and Torches category or check the Smoking Accessories wiki for more gear guides.
Swapping the flint takes approximately 10 seconds and requires no tools, no force, and no prior experience. Here's the full process:
We've been selling Clipper lighters and accessories since the early days of the shop — over 20 years now — and the single most common question we get is: "My Clipper won't light — is it broken?" Nine times out of ten, the gas is fine. The flint is just spent. People refill the gas, try to spark it, get nothing, and assume the lighter is dead. It's not. A fresh flint component restores ignition in seconds — no replacement lighter needed.
Honest limitation worth mentioning: if your Clipper's gas valve has been damaged (usually from over-tightening a refill canister), a new flint won't help. You'll get a spark but no gas flow. In that case the lighter body itself needs replacing. We see this maybe once in every 50 cases — it's rare, but worth knowing so you don't buy flints expecting them to solve a valve issue.
We'd recommend keeping 2 or 3 spare flints around. Toss one in your rolling tray, one in your jacket pocket, one in a drawer. They're tiny, they weigh practically nothing, and the moment you need one, you'll be glad it's there rather than having to borrow someone else's lighter at a party. Get a few extras while you're ordering — future you will appreciate it.
Compared to buying a new disposable lighter every week, a single Clipper with occasional flint and gas refills costs roughly 80% less over a year — and produces almost zero waste. It's one of those rare cases where the cheaper option is also the better one. If you want to compare refillable options side by side, our Lighters and Torches product category page has the full range, and the Clipper blog post covers long-term maintenance tips.
It depends on how heavily you use it, but most daily users get 2 to 4 weeks from a single flint. You'll notice the spark getting weaker before it dies completely — that's your cue to swap it out.
No. This is a Clipper-specific flint ignition component — the assembly includes the striking wheel and spring housing designed for Clipper lighters only. Zippo flints are a different diameter (2.4 mm vs 2.0 mm) and length.
Absolutely. Pull the assembly out by the wheel and you've got a firm, straight poker. It works best when the flint is fresh — a worn flint rod is shorter and less rigid.
Probably not. If you're getting a spark, the flint is working. The issue is likely an empty gas reservoir. Refill through the valve on the base of the lighter and try again.
The striking wheel will spin freely with almost no resistance and produce no visible spark. At that point the ferrocerium rod has worn down to nothing and needs replacing.
Not really — the flint wears down with every strike, and that's by design. Keeping the lighter dry and clean helps the wheel grip the flint properly, so you get a spark on the first flick rather than grinding through multiple attempts.
You can order them right here at Azarius. We stock them individually and they ship with all standard orders. Check our Smoking Accessories category for related gear.
Last updated: April 2026
